Star Micronics TSP828L Series Bedienungsanleitung

Label PRINTERTSP828L SERIESHardware Manual

– 7 –(5) Connect the interface cable to the connec-tor on the rear panel of the printer.(6) Fasten the connector clasps.Parallel interfacecable3-3. In

– 8 –3-4. Connecting the AC AdapterNote:Before connecting/disconnecting the AC adapter, make sure that power to the printerand all the devices connect

– 9 –Power switch3-5. Turning Power OnMake sure that the Power cord has been connected as described in 3-4.Turn ON the power switch located on the fro

– 10 –3-6. Loading the Roll Paper3-6-1. Thermal Label Roll Paper (Peel Mode)CAUTIONWhen using a thermal label roll paper, do not install the tension b

– 11 –(6) Peel off a label that is within 150 mm fromthe end of the roll paper, and place the rollpaper in the direction shown.(7) Pull out the end of

– 12 –(9) Turn the end of the backing paper back-ward.(10) Push both sides of the printer cover withyour hands as shown, until the printercover is sec

– 13 –3-6-2. Thermal Label Roll Paper (Tear Bar Mode)CAUTIONWhen using a thermal label roll paper, do not install the tension bar, two tension folders

– 14 –(6) Peel off a label that is within 100 mm fromthe end of the roll paper, and place the rollpaper in the direction shown.(7) Pull out the end of

– 15 –(11) Press the FEED button to bring up theleading edge of the roll paper.Note: If the leading edge of a label is notdetected after 300 mm or mor

– 16 –(6) If the thickness of the paper is 65 to 99 µm, install the tension bar on the printer as shown.If the thickness of the paper is 100 to 150 µm

Federal Communications CommissionRadio Frequency InterferenceStatementThis equipment has been tested and found to comply with the limits for a Class A

– 17 –(8) Pull out the end of the roll paper towardsyou.(9) Leaving the paper as is, close both theouter and inner covers. Push both sides ofthe print

– 18 –WARNING• Do not touch the tear bar blade.- There is a tear bar blade inside the paper outlet slot. Not only should you not put your handin the p

– 19 –4. Thermal Roll Paper SpecificationWhen consumable parts have run out, use those specified below.Note:Access the following URL for the informati

– 20 –• Recommended label paper:Print Density and Speed SettingsDepending on the type and thickness of the paper, it may be necessary to changethe set

– 21 –• Recommended label paper specifications:Use roll paper that meets the conditions below.Printing directionBase material(label paper)Peel paper (

– 22 –• Black Mark Specifications(1) Black mark pitchSet the black mark pitch A to be within a range of 36 to 304 mm.(2) Black mark dimensionsSet the

– 23 –(6) Effective printing range when using label paper with black mark specifications.2.5 minimum (left margin)103 (effective print width: 68 chara

– 24 –4-2. Thermal Roll Paper• Paper width: 45 ± 0.5 mm to 112 ± 0.5 mm• Paper thickness: 65 µm to 150 µm• Roll paper outer dimensionsRoll diameter: ø

– 25 –5. Control Panel and Other Functions5-1. Control Panel1 POWER lamp (Green LED)Lights when the power is ON.2 ERROR lamp (Red LED)Indicates variou

– 26 –2) Non-recoverable errorsError DescriptionHead thermistor errorPower voltage errorEEPROM errorFlash access errorSRAM errorPOWER LampOffOffOffOff

TABLE OF CONTENTS1. Unpacking and Installation ...

– 27 –5-4. Adjusting the SensorsThis printer is equipped with three types of paper sensors.A. Label roll paper transmission type sensorThis sensor det

– 28 –(6) If the two lamps remain ON after flashing, it means that the sensor is adjusted properly anddoes not require further adjustment.(7) If both

– 29 –(5) Press and hold the FEED button, and turnON the power switch of the printer. Thetwo lamps will flash on the control panel toindicate that the

– 30 –(6) After the lamps have flashed, turn the VR1 knob fully counterclockwise. The adjustment hasbeen completed if the POWER lamp is ON. Proceed to

– 31 –6. Preventing and Clearing Paper Jams6-1. Preventing Paper JamsThe paper should not be touched during ejection and printing.Pressing or pulling

– 32 –7. Periodic CleaningAt times, the printer might leave some characters partially unprinted due to paper particles ordebris from the adhesive used

– 33 –8. Specifications8-1. General Specifications(1) Printing method Direct line thermal printing(2) Print speed Max. 150 mm/sec.(3) Dot density 203

– 34 –8-2. Interface• Bidirectional parallel interface: IEEE 1284 compatibility and nibble modes• Dual interface: RS-232 D-Sub 9 pinUSB USB type-B c

– 35 –(%RH)34°C 90% RH40°C 65% RH45°C 50% RH90806040201001020Temperature (°C)Operating environmentrangeRelative humidityOperating temperature and humi

– 36 –9. Dip Switch SettingTwo DIP switches are provided at the bottom of the printer, and can be set as given in the tablebelow. Be sure to set the p

– 1 –1. Unpacking and Installation1-1. UnpackingAfter unpacking the unit, check that all the necessary accessories are included in the package.Fig. 1-

– 37 –9-1. Parallel Interface TypeON ONOFF OFFDIP-SW 1Switch Function ON OFF1-1Command emulation See table below1-21-3Should not be changed (Should be

– 38 –9-2. Dual Interface Type<Switching the Dual Interface Modes>The dual interface enables the connection of an RS-232 interface and a USB int

– 39 –DIP-SW 2Switch Function ON OFF2-12-2Always ON Should be set to on2-32-4The factory settings of DIP switch are all on.9-2-2. RS-232 Interface Typ

– 40 –DIP-SW 2Switch Function ON OFF2-12-2Always ON Should be set to on2-32-4 DIP Switch 3The factory settings of DIP switch are all on.The following

– 41 –DIP-SW 3Switch Function ON OFF3-1Baud Rate See table below3-23-3 Data Length 8 bits 7 bits3-4 Parity Check Disabled Enabled3-5 Parity Odd Even3-

– 42 –Parallel interface connector (printer side)This connector mates with anAmphenol 57-30360 connector10. Parallel InterfaceThe two-way parallel int

– 43 –11. Dual Interface11-1. RS-232 Interface11-1-1. Interface Specifications1 Data transmission method: Asynchronous serial interface2 Baud rate: Se

– 44 –11-1-2. Connectors and Signal NamesRS-232Pin No. Signal name Direction Function– FG — Frame ground1 N.C — Not used2 RXD IN Receiving data3 TXD O

– 45 –11-1-3. Cable ConnectionsThe followings are a recommended interface cable connections.Note:Use shielded wire less than 3 m in length.11-2. USB I

– 46 –12. Memory Switch SettingsEach memory switch is stored in EEPROM. For details on the functions and settings of memoryswitches, see the separate

– 2 –2. Parts Identification and NomenclatureDual Interface ModelPrinter coverOpen this cover toload or replace paper.Do not open the coverwhile print

2006.01.18Printed in China, 80870460CDELECTRONIC PRODUCTS DIVISIONSTAR MICRONICS CO., LTD.536 Nanatsushinya, Shimizu-ku, Shizuoka,424-0066 JapanTel: 0

– 3 –Choosing a place for the printerBefore actually unpacking the printer, you should take a few minutes to think about whereyou plan to use it. Reme

– 4 –3. Setup3-1. Connecting the Cable to the PC3-1-1. USB Interface cableConnect the USB interface cable to a USB port of your PC.Note:The dialog sho

– 5 –3-2. Connecting the Cable to the PrinterNote that the interface cable is not provided. Please use a cable that meets specifications.3-2-1. USB In

– 6 –3-2-2. RS-232 Interface Cable(1) Make sure the printer is turn off.CAUTIONBefore connecting/disconnecting the interface cable, make sure that pow