Star Micronics LC24-20 Bedienungsanleitung Seite 31
- Seite / 194
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Loading the paper
1. Place a stack of fanfold paper behind and below the printer.
2. Turn the printer’s power OFF.
3. Pull the release lever toward the front of the printer ( ~ ). This has the
effect of releasing the paper from the platen roller, and engaging the
tractor feed.
4 Open the mute cover on the front cover, as shown in Figure 3-4.
, Release level
Figure 3-4. Opening the mute cover and correct lever position.
5. Open the rear cover using the two grips on either side, as in Figure 3-5.
Figure 3-5. Opening the rear cover.
6. Pass the paper between the printer case and the rear cover.
23
- -20MULTI-FONT 1
- Trademark Acknowledgements 2
- HOW TO USE THIS MANUAL 3
- TABLE OF CONTENTS 5
- Chapter 6 TROUBLESHOOTING 6
- Chapter 9 DOWNLOAD CHARACTERS 7
- Chapter 11 REFERENCE 7
- INTRODUCTION 9
- PRINTER COMPONENTS 10
- Mute cover 11
- Rear cover 11
- Entry slot 11
- Control panel 11
- SUMMARY OF PRINTER FEATURES 12
- Paper parking 13
- Print styles 13
- 11111111111111111 14
- Quad-s i zMI 15
- SETTING UP THE PRINTER 17
- UNPACKING 18
- AND INSPECTION 18
- SETTING UP 20
- Installing the platen knob 20
- Removing the front cover 21
- Installing the front cover 23
- Installing the paper guide 24
- Installing the mute cover 24
- &“”””” 25
- PAPER INSTALLATION AND USE 27
- Bottom of 0 28
- ADJUSTING THE PRINTING GAP 29
- LOADING FANFOLD FORMS 30
- Loading the paper 31
- Tractor cover 32
- Paper unparking 35
- Tear off function 35
- LOADING SINGLE SHEETS 36
- EJECT/PARK] 37
- D ‘ONT‘lTCH 39
- ‘J’’’::&’EE 39
- PAPER FEED 40
- EJECT/PARK 41
- L-J ‘“NT‘“c” 43
- Long test mode 44
- Print area test mode 45
- Pitch lock mode 45
- Font lock mode 45
- Font and Pitch lock mode 45
- SETTING 2 * * 46
- Hexadecimal dump 48
- .“’cRO’”” 49
- L----J ‘“NT““” 49
- Forward micro-feed 50
- Reverse micro-feed 50
- Clearing the buffer/All reset 51
- Save Macro Definition 51
- ● Current Font 52
- ● Current pitch 52
- Summary of display messages 53
- Summary of beep tones 55
- I I 1 1 r’ 57
- FUNCTIONS OF THE EDS SETTINGS 58
- AutoLF with CR 59
- CanadianFrench ON 61
- Multi-1 ingual OFF ON 61
- TROUBLESHOOTING 65
- PAPERFEEDI button 67
- ● . Printer is noisy 71
- MAINTENANCE 72
- OPTIONAL ACCESSORIES 73
- Setting up 74
- Loading paper 76
- Feeding a single sheet 78
- PULL TRACTOR UNIT (PT-IOZS) 79
- Printer co 80
- Clamp lever 82
- ABCDE ABCDE 83
- ABCDE abcde 83
- Close the front cover 85
- INTERFACE CONVERTER (SPC-8K) 86
- XONIXOFF 87
- PRINTER CONTROL COMMANDS 89
- Select print quality 90
- I<ESC> “[” 90
- Select LQfont 90
- Select italic characters 91
- Select upright characters 91
- Emphasized printing 91
- Cancel emphasized printing 91
- Double-strike printing 92
- Cancel double-strike printing 92
- Underlining 92
- Overlining 92
- Select score 93
- Select ornament character 93
- Superscript 93
- Subscript 94
- Select standard character set 95
- Select IBM character set 95
- Select character set #l 95
- Select character set #2 95
- Select IBM codepage 96
- Select slash zero 97
- Select normal zero 97
- Pica pitch 98
- Elite pitch 98
- Semi-condensed pitch 98
- Condensed printing 98
- Cancel condensed printing 99
- Proportional spacing 99
- Selectfont and pitch 100
- Expanded printing 100
- Select character width 101
- Select master print mode 101
- Increase character spacing 101
- Return to normal height 102
- Onm 00 00 n m 103
- Set line spacing to 1/8 inch 104
- Set line spacing to 1/6 inch 104
- Set line spacing to n1360inch 104
- Set base unitfor line spacing 105
- Execute &SC> “A” 106
- Linefeed 106
- Reverse linefeed 106
- Selectforward feed mode 106
- Select reversefeed mode 106
- Feed paper n lines 107
- IBoth I <ESC> “N” n 108
- Form feed 109
- Return to top of current page 109
- Disable paper-out detector 109
- Enable paper-out detector 109
- Set vertical tab stops 110
- Select vertical tab channel 110
- Vertical tab 111
- Set left margin 112
- Set right margin 112
- Set left and right margins 113
- Carriage return 113
- Set automatic linefeed 113
- Cancel automatic linefeed 113
- Backspace 113
- Leftjust$y 114
- Center text 114
- Rightjustify 114
- Fulljustify 114
- Set horizontal tab stops 114
- Reset all tab stops 115
- Horizontal tab 115
- Relative horizontal tab 115
- GRAPHICS COMMANDS 117
- 1B 5A n/ /72 118
- Select graphics mode 119
- Convert graphics density 120
- Define download characters 121
- IB 3A 00 II 00 123
- Select download character set 124
- Shift download character area 124
- Select ROM character set 124
- Set h4SB to 1 125
- Set MSB to O 125
- Accept MSB as is 125
- Delete last character sent 125
- Cancel last line 125
- Set printer off-line 126
- Set printer on-line 126
- Stop printing 126
- Bi-directional printing 126
- Uni-directional printing 127
- Manualfeed 127
- Auto feed 127
- Eject paper from ASF 127
- Reset printer 128
- Set initial conditions 128
- DOWNLOAD CHARACTERS 129
- Assigning the character data 130
- “X 1 “ ; 132
- DIFFUSION RANGES OF 133
- CARS & TELEPHONES 133
- I I ~ ~ ~ ~ I 135
- ●10100.00,001.- -1 136
- Sample program 138
- ‘ Dot Pattern Data 139
- MS-DOS AND YOUR PRINTER 141
- ● Letter quality 142
- PROGRAMMING WITH BASIC 144
- 0, 0, 63 146
- 3520 DATA 147
- 1, (1, o 147
- How the program works 149
- REFERENCE 151
- PINOUT OF INTERFACE CONNECTOR 155
- Parallel interface 155
- Serial Interface 156
- Charactel 157
- —Control code — Decimal value 157
- -Hexadecimal value 157
- (loworder) 157
- Standard character set #2 158
- International character sets 160
- Code Page #437 (U.S.A.) 161
- Code Page #860 (Portuguese) 164
- Code Page #861 (Icelandic) 165
- Code Page #865 (Nordic) 167
- Character set #1 168
- PROPORTIONAL SPACING TABLE 170
- Character code 171
- Proportionalwidth 173
- Proportional width 174
- 11 36 24 36 174
- NormalSupedSub 175
- Std. #437 #850 #860 #861 179
- #863 #865 179
- Fanfold forms, loading, Z-27 182
- Linefeed, 98 183
- Pitchcommands, 90-95 183
- COMMAND SUMMARY 185
- . . . . ~ 187
- IBM Mode 188
- Selectinitialconditions 189
- Consumer Response 190
- CONTROL PANEL OPERATIONS 191
- Savemacro 191
- I(Seetable3 and4) 192
- IGerm.n.iON i OFF 192
- PRINTED IN JAPAN 194
Verwandte Produkte und Handbücher für Etikettendrucker Star Micronics LC24-20
(50 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.224 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern