Star Micronics FUTUREPRINT TSP100 Bedienungsanleitung Seite 1

Hardware Manual

– 7 –3-3. Loading the Roll PaperBe sure to use roll paper that matches the printer’s specification.When using a paper roll with an 57.5 mm width, inst

– 8 –Note: When using a paper roll with an57.5 mm width, install the paper rollholder in the groove in the printer.If a paper roll with a 57.5 mm widt

– 9 –WARNING• Do not touch the cutter blade.- There is a cutter inside the paper outlet slot. Not only should you notput your hand in the paper outlet

– 10 –3-4. Connecting the USB Cable to the PCConnect the USB interface cable to a USBport of your PC.Note: The dialog shown below may appearon your PC

– 11 –3-6. Connecting the Power CordNote: Before connecting/disconnecting the power cord, make sure thatpower to the printer and all the devices conne

– 12 –Power switch3-7. Turning Power OnMake sure that the Power cord has been connected as described in 3-6.(1) Turn ON the power switch located on th

– 13 –4-1. Attaching the Holder Plate(1)Attach the holding plate to theprinter. Then tighten the two screwsthat were supplied to secure it inplace.(2)

– 14 –4-2. Attaching the Rubber Feet(1) Attach the four rubber feet in thepositions shown in the figure.Ensure that any soiling has beencompletely wip

– 15 –4-3. Switch Blind InstallationIt is not necessary to install the switch blind. Only install it if it is necessary foryou. By installing the swit

– 16 –5. Termal Roll Paper SpecificationWhen consumable parts have run out, use those specified below.(1) Roll paper specificationThermal paperThickne

Federal Communications CommissionRadio Frequency InterferenceStatementThis equipment has been tested and found to comply with the limits for a Class A

– 17 –6. Control Panel and Other Functions6-1. Control Panel1 POWER lamp (Green LED)Lights when the power is ON.2 ERROR lamp (Red LED)Indicates variou

– 18 –2) Non-recoverable errorsNote:1) If a non-recoverable error occurs, turn the power OFF immediately.2) If a non-recoverable error occurs, please

– 19 –6-3. Self-PrintingTest PrintingTurn the power ON while holding the FEED button depressed. The printer willrun a test print according to the Ver.

– 20 –7. Preventing and Clearing Paper Jams7-1. Preventing Paper JamsThe paper should not be touched during ejection and before it is cut.Pressing or

– 21 –7-3. Releasing a Locked Cutter (Auto Cutter Mode only)If the auto cutter locks up or fails to cut the paper, follow the steps below.WARNINGSince

– 22 –(4) If the cutter is locked, insert a Philips screwdriver into the Philips screw holeon the side of the cutter, and turn it in the direction of

– 23 –8. Periodical CleaningPrinted characters may become partially unclear due to accumulated paper dustand dirt. To prevent such a problem, paper du

– 24 –ECR3 R4R3= 3.5kΩR4= 300ΩBModular plugPeripheral Drive ConnectorPin No.SignalFunctionI/Oname direction1 FG Frame ground —2 DRD1 Drive signal 1 OU

– 25 –Notes: 1. Pin 1 must be shield drain wire connected to peripheral deviceframe ground.2. It is not possible to drive two drives simultaneously.3.

– 26 –10-1.General Specifications(1) Printing method Direct line thermal printing(2) Print speed Max. 1000 dots/sec. (125 mm/sec.)(3) Dot density 203

TABLE OF CONTENTS1. Unpacking and Installation ...11-1.Unpacking ...

– 27 –10-2.Auto Cutter Specifications(1) Cutting frequency Max. 20 cuts per minute(2) Thickness of paper 65~85 µm10-3.Interface(1) Specifications USB

– 28 –10-6.Reliability1) Life Mechanical: 20 million linesHead: 100 million pulses, 100 km (±15% max. aver-age head resistance fluctuation)For 2-color

2005.08.20Printed in China, 80870415CDELECTRONIC PRODUCTS DIVISIONSTAR MICRONICS CO., LTD.536 Nanatsushinya, Shimizu-ku, Shizuoka,424-0066 JapanTel: 0

– 1 –1-1. UnpackingAfter unpacking the unit, check that all the necessary accessories are included inthe package.Fig. 1-1 UnpackingIf anything is miss

– 2 –2. Parts Identification and NomenclatureCover open leverPull this lever in thedirection of thearrow to open theprinter cover.Control panelFeature

– 3 –Tear Bar ModelCover open leverPull this lever in thedirection of thearrow to open theprinter cover.Power connectorFor connection ofthe power cord

– 4 –Choosing a place for the printerBefore actually unpacking the printer, you should take a few minutes tothink about where you plan to use it. Reme

– 5 –3. Setup3-1. Connecting the USB Cable to the PrinterAffix the ferrite core onto the USB interface cable and pass the cable through thecable suppo

– 6 –3-2. Connecting to a Peripheral UnitYou can connect a peripheral unit to the printer using a modular plug. Thefollowing describes how to install